INTERNATIONAL PARTS

IH BIG INPUT SHAFT $650.00

• FITS 706-1466

IH CUSTOM TRANSMISSION GEARS

• FITS 706-1466
• CONSTANT MESH GEARS  $575.00
• THIRD GEAR  $575.00
• FIRST AND SECOND CLUSTER GEAR   $1100.00

IH NEEDLE BEARING DIFF $1000.00

• AVAILABLE FOR 460-1466
• THIS INCLUDES ALL PARTS AND MACHINE WORK NEEDED WITH YOUR CARRIER HOUSING

IH NEEDLE CROSS $500.00   CLICK HERE

• AVAILABLE FOR 460-1466

IH BRONZE BEVEL WASHERS $35.00 EACH CLICK HERE

• AVAILABLE FOR 460-1466

IH SIDE GEAR HRUST BEARING AND RACE  $65.00 EACH

• FITS 460-1466

IH SPIDER GEAR MACHINED        $25.00 EACH WITH EXCHANGE

• MACHINED FOR USE WITH BRONZE BEVEL WASHER
• FITS 460-1466

IH TAPER LOCK HUB FOR USE WITH FLUID DAMPER $425.00

IH COUNTER SHAFT SUPPORT $425.00

• FITS 706-1466
• RECOMMENDED WHEN RUNNING THIRD GEAR TO KEEP SHAFT FROM FLEXING

IH 400 SERIES GIRDLE $950.00

• COMES WITH 7/8 THICK GIRDLE, SPACER BLOCKS, BOLTS AND WASHER, AND OIL PUMP PICK UP ADAPTER BLOCK

IH 466 SERIES ENGINE KIT INCLUDES VALVE RELIEF CUT IN PISTONS AND FIRE RING GROOVES CUT IN SLEEVES WITH FIRE RINGS $1250.00

IH 400 SERIES HEAD GASKET AND FIRE RING KIT  $117.00

IH ADJUSTIBLE CAM GEAR $650.00 BILLET GEAR CLICK HERE

• ALLOWS FOR 10 DEGREES OF TIMING EITHER DIRECTIONAT A RATE OF 1.5 DEGREES PER HOLE

IH COMPLETE HITCH ASSEMBLY $850.00 CLICK HERE

IH HITCH ASSEMBLY (YOU WELD) $675.00

HARDENED DRAWBAR   $325.00  CLICK HERE

HARDENED DRAWBAR PIN   $20.00

HITCH ADJUSTMENT BOLTS   $75.00 FOR 3

ADJUSTMENT HORSESHOE  $60.00

IH WELD ON AXLE HUBS WITH SHAPE $375.00 CLICK HERE

WELD ON AXLE HUBS WITH NO KEY $325.00

IH DISK BRAKE KITS $910.00

• INCLUDES BRAKE ROTORS, BRAKE PADS, BRAKE CALIPERS, BRAKE PEDALS, MASTER CYLINDER AND RESERVOIR, CALIPER BRACKETS
• REQUIRES MACHINING OF SEAL PLATE ADDITIONAL $150.00

IH DISK BRAKE ROTORS $175.00 A PAIR CLICK HERE

IH FRONT MOUNT FUEL SUPPLY PUMPS $815.00 CLICK HERE

• FITS 300- 400 SERIES

IH IDLER SUPPORTS $75.00   CLICK HERE

• FITS 300-400 SERIES
• REQUIRES HOLE MACHINED IN FRONT COVER ADDITIONAL $75.00

IH FRONT COVER    $300.00 WITH EXCHANGE

• WATER PUMP REMOVED
• CAM ACCESS HOLE
• IDLER SUPPORT HOLE

IH BILLET ROLLER ROCKERS CLICK HERE

• FITS 300-400 SERIES
• WITH ADJUSTORS $500
• WITHOUT ADJUSTORS $425

IH WATER INLET BLOCK     $50.00 CLICK HERE

• FITS 300-400 SERIES
• REQUIRED WHEN CUTTING FACTORY WATER PUMP OFF THE FRONT COVER

IH OIL COOLER ELIMINATOR     $60.00  CLICK HERE

• FITS 300-400 SERIES
• REQUIRED WHEN REMOVING OIL COOLER

IH STEEL QUILL HOUSING 400.00 CLICK HERE

CUMMINS PARTS

5.9 CUMMINS BILLET ADJ CAM GEAT $650.00  CLICK HERE

• ALLOWS FOR 10 DEGREES OF TIMING EITHER DIRECTIONAT A RATE OF 1.5 DEGREES PER HOLE

5.9 CUMMINS 12V ADJ PUMP GEAR $375.00 EXCHANGE GEAR

CLICK HERE

• ALLOWS FOR 10 DEGREES OF TIMING EITHER DIRECTIONAT A RATE OF 1.5 DEGREES PER HOLE

5.9 CUMMINS GIRDLE KIT $1000.00 CLICK HERE

• INCLUDES GIRDLE, SPACER BLOCKS, AND 14 MM STUDS
• REQUIRES SPACER TO BE MACHINED TO FIT BLOCK AND CHECK LINE BORE

5.9 CUMMINS BILLET FRONT COVER $450.00 CLICK HERE

• ALLOWS FOR ACCESS TO ADJUST CAM GEAR AND PUMP GEAR
• FUEL SUPPLY OPTION   $600

NV4500 BILLET INPUT SHAFTS $650.00 CLICK HERE

•  1 3/8 INCH UPGRADE
• MADE IN USA
• IF PURCHUSED WITH ONE OF OUR CLUTCHES $500.00

JOHN DEERE PARTS

SBJD GIRDLE $850.00 CLICK HERE

• 7/8 INCH THICK
• INCLUDES SPACER BLOCKS AND BOLTS

SBJD TAPER LOCK HUB FOR USE WITH FLUID DAMPER $450.00

CLICK HERE

SBJD INPUT SHAFTS $450.00 CLICK HERE

BBJD TAPER LOCK HUB FOR USE WITH FLUID DAMPER $450.00

CLICK HERE

FORD PARTS

FORD TAPER LOCK  $450.00 CLICK HERE CLICK HERE

• SPECIFY 6 BOLT OR 8 BOLT CRANK FOR BORE SIZE IN HUB
• FOR USE WITH FLUID DAMPER

 FORD BILLET ADJUSTABLE CAM GEAR $650.00

• FITS 405-474 ENGINES
• ALLOWS FOR 10 DEGREES OF TIMING EITHER DIRECTIONAT A RATE OF 1.5 DEGREES PER HOLE

AC PARTS

AC 301 BILLET MAIN CAPS  $800.00

• REPLACES FACTORY CAPS TO USE WITH GIRDLE
• REQUIRES LINE BORING

AC 301 GIRDLE KIT    $800.00

• INCLUDES 3/4 INCH THICK GIRDLE AND BOLTS

AC 426 ROLLER ROCKER ARMS  $450.00

AC426 GIRDLE KIT   $900.00

• INCLUDES 3/4 INCH THICK GIRDLE, SPACER BLOCKS, AND BOLTS

AC 426 ADJUSTABLE CAM GEAR  $475.00 EXCHANGE OLD GEAR

• ALLOWS FOR 10 DEGREES OF TIMING EITHER DIRECTIONAT A RATE OF 1.5 DEGREES PER HOLE

UNIVERSAL FITS ANY ABOVE TAPER LOCK HUBS

12.3 IN FLUID DAMPNER WITH TIMING MARKS $465 CLICK HERE

• AVAILABLE FOR IH, BBJD, SBJD, AND FORD

 GUILLOTINE AIR KILL  $90.00

• AVAILABLE IN MANY SIZES